24V Liquid Cooler (Heat & Cool)

• Laser devices
• Battery packs
• Medical equipment
• Photonics effective cooling
• Small chilled water systems
• Electronics cooling systems
• Electric vehicle charging stations
• Semiconductor test industry application
• Besides, you also can combine RIGID Liquid Chiller LC3220E-H with a cooling shirt or vest, which is a compact chiller for human body cooling. Chiller LC3220E-H circulates water flowing through the suit, helping to take away the heat released by the human body.
• LC3220E-H works as a liquid chiller to cool the circulating water and provide continuous cooling water for the human body cooling.

The Chiller LC3220E-H has one of the highest power-to-weight ratio rotary micro-compressor in the world. Capable of producing as much cooling power as a compressor 5x its size – this is the heartbeat of our cooling system

It is dual functions of Heating and Cooling. Easy & Swift. The Chiller LC3220E-H requires no ice! It adopts the world’s smallest variable speed refrigerated compressor to operate. Small body, Power engine. Driven by a dc power supply (24V), it runs on a continuous cooling cycle, therefore will cool
as long as the system is turned on.
It’s extremely lightweight, and compact, and has a fluid flow rate of 5 liters per minute at 16psi. The rotary micro-compressor inside is as strong as other systems 5 times its size.
It requires zero maintenance and allows you to set and change your temperature to your
needs.

Usually, distilled water is good if your target liquid temperature is above 4C degree.
If you want a much lower liquid temperature, you have to consider Coolant Formula to avoid frostings, like propylene glycol or water mixtures.

Factory setting is 4ºC ~45ºC (39ºF ~113ºF). We can customize according to the customer’s special demands.

The recommended temperature setting is 13ºC (55º F). We recommend this mid-range temperature because studies show that temperatures below 55º can shock the capillaries just below the surface of the skin and cause them to close, actually causing your body to hold heat. 55º – 60º around the torso and vital regions of the body is most effective, cooling your body from the core.

The Chiller LC3220E-H functions on a continuous cycle. Your device’s operating frequency and how often you use the system effects how often you need to refill the reservoir. Chiller LC3220E-H only requires one to one coolant formula for distilled water mixture, so we recommend topping off before every use to prevent the system from running dry.

External dimension: 339x208x235 mm (13×8.2×9.2 inch)
Net weighs: 5kgs/11lbs

A digital display in front of the chiller communicates the current temperature.

Depending on the ambient temperature at the time, your system and install. RIGID also provides customized service and design.

While power draw can spike to 12 amps max, depending on your surrounding temperature, average draw is 4-5 amps. The system runs on 24 volts AC adapter. Tested in maximum compressor speed at 6000rpm, our system uses around 550 watts at maximum. We highly recommend adding an inline fuse within 6 inches from the power supply, inlinewith fans and ducting to prevent from heat soak and high amp draw. Forcing ambient air intake to the chiller can significantly affect the draw rate.

The RIGID Compact Cooler requires a 24V 10 amp or greater power supply. We recommend you install to accessory and add an inline fuse within 6 inches of the power supply.

Note* the red wire is positive, the black is ground. Mount the base plate. The mounting location should be in the coolest, most ventilated portion of the system. Cooler air will boost efficiency and reduce current draw, therefore, mount the system where the intake is facing away from the transmission tunnel and exhaust. Do not mount the system over the transmission tunnel or exhaust.

We recommend you use 1″-1.5″ spacers between the cooler and the floor pan to allow cooler air to circulate under the system to prevent overheating. In some devices, a duct and blower may be necessary to source cooler air. Operating temperatures should not exceed 60º C / 140º F without additional fans or blowers.

If the temperature exceeds 140º F, the system will shut off to prevent overheating. Consider the shorter the length of the cooling hose, the more efficient the hose will be. Hoses can be cut to fit and shrink-wrapped for a clean, finished look. Visit our website for more videos and tips. WWW.RIGIDHVAC.COM

There are zero maintenance requirements for Chiller LC3220E-H. We only suggest that you top the Coolant Formula off before every use to prevent it from ever running the system dry.

RIGID Cooling Systems offer replacement and spare installation parts. If you have
additional questions about which parts you might need, please reach out to us. www.rigidhvac.com * info@rigidhvac.com * +86-579-8837 9768

Liquid Chiller LC3220E-H is a completed cooling system. It is fully charged with refrigerant
gas and oil before shipping. Just plug and play!
Optional accessories:
 AC Adaptor
 Cooling hose

You should not put freon inside of the Chiller LC3220E-H except distilled water and
glycol-water mixture for this type of compressor. Any other fluids including freon could cause the system to freeze up or congeal, evidently breaking the system.

RIGID Compact Cooling Systems is selling direct to consumers. Retails feel free to our
online store: https://www.rigidhvac.com/online-order
For production orders or cooperation, reach out to ann@rigidhvac.com Any comments will
receive our prompt reply in 12hrs.

The warranty of Chiller LC3220E-H is 18 months.

All RIGID cooling systems ship internationally, DHL door-to-door shipping.